Студопедия
Случайная страница | ТОМ-1 | ТОМ-2 | ТОМ-3
АвтомобилиАстрономияБиологияГеографияДом и садДругие языкиДругоеИнформатика
ИсторияКультураЛитератураЛогикаМатематикаМедицинаМеталлургияМеханика
ОбразованиеОхрана трудаПедагогикаПолитикаПравоПсихологияРелигияРиторика
СоциологияСпортСтроительствоТехнологияТуризмФизикаФилософияФинансы
ХимияЧерчениеЭкологияЭкономикаЭлектроника

L, N and R models

Читайте также:
  1. A Pulse generator coil wiring connector (arrowed) - J and К models
  2. Advocacy for Essentialist Gene Models for Psychiatry
  3. American pronunciation models.
  4. B Shock absorber lower mounting bolt (arrowed) - L, N and R models
  5. Categorical Gene Models and the Problem of Small Effect Size
  6. Classification of pronunciation variants in English. British pronunciation models.
  7. Early Evidence on the Plausibility of Essentialist Gene Models for Psychiatry

8 Remove the screw securing the turn signal lens and remove the lens, noting how it fits (see illustration).

9 Turn the bulbholder anti-clockwise and withdraw it from the lens (see illustration).

 

10 Push the bulb into the holcer and twist it anti-clockwise to remove it (see illustration). Check the socket terminals for corrosion and clean them if necessary. Line up the pins of the new bulb with the slots in the socket, then push the bulb in and tun it clockwise until It locks into place. The front turn signals on the R model double as running lights and use dual filament bulbs; the pins on the bulb are offset so it can only be installed one way.

11 Fit the bulbholder back into the lens and turn it clockwise, making sure It is securely held.

12 Fit the lens onto the holder. Locate the clip on the side of the lens behind the tab in the housing (see illustration).

13 Turn signal assemblies -

 

removal and installation

Removal

1 Disconnect the turn signal wiring connectors. On the front turn signals, they are on the inside of the fairing (on J and К models. you can either disconnect the connector or


And remove the bulb

remove the bulbholder) (see illustrations). On the rear turn signals, remove the seat (J and К models) or the seat cowling (L, N and R

A Front turn signal wiring connector-J and К models

C Rear turn signal wiring connectors (arrowed) - J and К models


Locate the clip (A) behind the tab (B)

models) (see Chapter 8) - the connectors are inside a rubber boot which is secured by a clip (see illustrations).

B Front turn signal wiring connectors - L, N and R models

13.1d Rear turn signal wiring connectors Q (arrowed) - L, N and R models


9»10 Electrical system


Turn signal screw (arrowed)


A Front turn signal screw (arrowed)


B Rear turn signal screw (arrowed)


 



14.5 Disconnect the wiring connectors (arrowed)...

2 On J and К models, to remove a front turn signal, remove the screw securing the signal to the inside of the fairing and remove it. noting how it fits (see illustration).

3 On J and К models, to remove a rear signal, either remove the screw securing the turn signal to its bracket, or remove the screw securing the bracket to the inside of the mudguard (see illustration 13.4b). Remove the turn signal, taking care not to snag the wiring as you pull it through.

4 On L, N and R models, remove the screw securing the assembly to either the inside of the fairing or rear mudguard (see illustrations). Remove the assembly, noting the arrangement of the mounting base and collar, and taking care not to snag the wiring as you pull it through.


Installation

5 Installation is the reverse of removal. Check the operation of the turn signals.

14 Brake light switches -

I

check and replacement


Дата добавления: 2015-10-29; просмотров: 122 | Нарушение авторских прав


Читайте в этой же книге: Remove the split pin (A) and withdraw the clevis pin (B) | Remove the spacers from the wheel | Tighten all the clamp bolts to the specified torque | Front wheel bearings | Fitting new tyres | General information | А Lift the flap and unscrew the bolt... | D ... and remove the cowling | B ... and remove the battery | B A blown fuse can be identified by a break in its element |
<== предыдущая страница | следующая страница ==>
Unscrew the nuts (arrowed) and remove the tail light| Removal - L, N and R models

mybiblioteka.su - 2015-2024 год. (0.005 сек.)